Is this the NIC card you have installed in your UPS?

Start the Network Management Card Device IP Configuration Utility. Enter the full IP address range of your network and click on the button to start the search for the UPS. The system will automatically locate the IP address of your APC UPS.

The Network Management Device IP Configuration Wizard only supports the discovery of unassigned devices. You cannot search for assigned devices already on the network using an IP range unless you enable SNMPv1 and set the Community Name to 'public'. For more information on SNMPv1, see the UserGuide. When the NMC IP address settings are configured, to access.
Schneider Electric Network Management Device IP Configuration Wizard. The Network Management Device IP Configuration Wizard is a Windows application designed specifically to remotely configure the basic TCP/IP settings of Network Management Cards. The Wizard runs on Windows® 2000, Windows.
By default, the APC AP9630 NMC (Network Management Card) does not have an IP address assigned. The easiest way to configure an IP address is to log into the UPS's NMC over a serial port. Many servers still come with a built-in 9-pin serial port, but most desktops and laptops do not.
APC Device IP Configuration Wizard-157. AP9617 Network Management Card Reset Smart Slot Link - RX/TX Status 10/100 10/100Base-T 8.

If so, have you tried using the 'Network Management Device IP Configuration Wizard' to configure it? If you don't have that application, you can download it from here:

Connect your UPS to the same network as the computer you are using to configure it. You can install the configuration wizard and follow the step-by-step instructions that you can find on that same page. I haven't done it in a while but from what I remeber it is very straight forward with that software.

AN!Wiki :: Configuring APC SmartUPS with AP9630 Network Cards

Apc network management device ip configuration wizard v5.0.3 download

Note: Depending on the firmware version, your screenshots may use the old APC branding and will differ significantly from the screenshots we use. An upgrade of the firmware should update your web interface.

This tutorial assumes a fresh configuration. If you've changed anything, you should reset your UPS to factory defaults.

Apc Network Management Device Ip Configuration Wizard

Contents

4Optional Changes

Antaira UTS-1110A single-port USB to RS-232] serial adapter. Photo by Antaira.

By default, the APC AP9630 NMC (Network Management Card) does not have an IP address assigned.

The easiest way to configure an IP address is to log into the UPS's NMC over a serial port. Many servers still come with a built-in 9-pin serial port, but most desktops and laptops do not. If you don't have one, many vendors sell USB to serial adapters. The one we've used quite successfully is the Antaira UTS-1110A, but almost any adapter you can find at your local computer store will work.

Note: The m2 Anvil! installs screen on both nodes and Striker dashboards.

We're going to use a program called screen to talk to the PDU over the serial port.

To do this, you need to know what device the PDU's serial cable is plugged into. Some common ones:

Type	Device path
Serial port 1	/dev/ttyS0
Serial port 2	/dev/ttyS1
USB-Connected port 1	/dev/ttyUSB0
USB-Connected port 2	/dev/ttyUSB1

.. and so on.

In my case, I'm using the first port on the USB to Serial adapter, so I will use '/dev/ttyUSB0'.

Knowing this, we're ready to go!

Open a terminal window and run:

Note: When you are done, to exit screen, press '<ctrl>' + 'a', release, then press 'k'. You will be prompted to kill the session, type 'y'.

The initial page will show nothing, so press <enter> a couple of times until the login prompt appears.

Enter 'apc'. If the UPS has not been configured before, the default password is also 'apc'. If someone has changed the password, you will need to use that.

Note: If you don't know what the current password is, use the password reset procedure.

When you login, you will see the default menu.

To reset to defaults, run:

You will be prompted to confirm.

Type 'YES'.

Note: Rebooting a UPS network card does NOT effect power. There will be no interruption to down-stream power.

Now reboot (and confirm):

The interface will stop responding for a while. Eventually it will come back to the login prompt. This time, the username and password are both 'apc'.

Apc Network Management Device Ip Configuration Wizard Windows 10

Press '<enter>' periodically until the login prompt comes back up.

Note: There is no default gateway on the BCN, so we will use the highest IP address in the subnet, despite nothing being there.

This will be an-ups01, so we will be setting the IP address to '10.20.3.1/24'. So knowing that, we can set the IP address of the UPS with this command:

Reboot, and the new IP will take effect.

Led edit software, free download for windows 7. Once the UPS reboots, you should be able to ping the UPS.

Excellent!

At this point, there is nothing strictly left to do. ScanCore's scan-apc-ups will be able to monitor the UPS without any further configuration.

If you want, however, we'll cover a few other configuration steps.

These will be done via the user interface. To log in, enter the new IP address into your browser.

APC AP9630 Login Screen.

Once you log in, this will be your default page.

Main page.

The optional sections below will all start from this point.

Note: The default inactive logout time is short. Expect to be redirected to the login page if you idle for more than a few minutes.

Change The Superuser Password

To change the password, use the following command. In this example, we'll set the password to 'secret'.

Mouse-over 'Configuration' -> 'Security' -> 'Local Users' and then click on 'Management'.

User management menu map.

This brings up the page with the three default user accounts; The one we care about, 'apc' and two system accounts that we don't care about, 'device' and 'read-only'.

Click on 'apc'.

Selecting the 'apc' user.

Now to change the password, enter the new password into the 'New Password' and 'Confirm Password' fields, then press 'Next >>'.

New password entered for the 'apc' user.

You will be shown a summary of what is about to be changed. Review and then click on 'Apply'

New password change summary.

Once applied, it will take you back to the user selection page. Log off and then back on to be sure that the new p